Victron MultiPlus 48/1200/13-16 230V VE.Bus - PMP482120000
Victron MultiPlus 500VA - 1600VA:
The new style MultiPlus is set to replace the earlier MultiPlus Compact range. It is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology and a high-speed AC transfer switch in a single compact enclosure.
In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.
When coupled with a GX device (e.g. Cerbo GX) you can monitor and control your Multi and system or systems' locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, from adjusting your Multi to auto starting a backup generator and more…
Models: 500VA, 800VA, 1200VA, 1600VA
NOTE: This unit requires installation by a licensed Electrician with Victron installation training.
Multifunctional, with intelligent power management- The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a highspeed AC transfer switch in a single compact enclosure. Next to these primary functions, the MultiPlus has several advanced features, as outlined below.
Parallel operation and three phase capability- Up to six Multis can operate in parallel to achieve higher power output. In addition to parallel connection, three units can be configured for three-phase output.
Power Control - Dealing with limited generator, shore side or grid power- With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.
Power Assist - Boosting the capacity of shore or generator power- This feature takes the principle of Power Control to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
Four stage adaptive charger and dual bank battery charging- The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software finetunes the three-stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on Victron's website, under Technical Information. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery.
High start-up power- Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
Search Mode- When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
Programmable relay- By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in the event of an alarm or a pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low).
Remote on / off / charger on- Three pole connector.
On-site system configuring, monitoring and control- After installation, the MultiPlus is ready to go. Some settings can be changed with DIP switches. 500/800/1200VA models: remote switch / battery charge voltage / inverter frequency /search mode.
1600/2000VA models: battery charge voltage /search mode. For more settings use VE-Config or the VE.Bus Smart dongle.
Remote configuring and monitoring- Install a Cerbo GX or other GX product to connect to the internet. Operational data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. When connected to the internet, systems can be accessed remotely, and settings can be changed.
SolarBox Australia will process your order within 1-2 business days. For product availability you can call us, use the chat function or email SolarBox directly at: email@example.com. If there is a delay on your order or your item is out of stock you will be emailed immediately to let you know.
Shipping prices are calcuated at checkout depending on weight and where it is being shipped to. View the shipping rules here
What is a warranty? A warranty is a voluntary promise offered by the person or business who sold the product or service to you. Once you buy the product or service, the promise becomes a right that can be enforced under the ACL. Warranties are separate from your automatic consumer guarantees. The consumer guarantees which apply regardless of any warranties suppliers sell or give to you, apply for a reasonable time depending on the nature of the goods or services. This means consumer guarantees may continue to apply after the time period for the warranty has expired.
View the product warranty page here for more information.