Victron Skylla-i 24/100(3) 230V - SKI024100002
Victron Skylla-i 24/100(3) 230V - SKI024100002
Must be installed by Electrician
Victron Energy Logo

Victron Skylla-i 24/100 (3) 230V - SKI024100002


Regular price $2,771.01 Sale price$2,355.36
/
Tax included. Shipping calculated at checkout.

Victron Skylla-I Charger:


A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air.

• The right amount of charge for a lead-acid battery: variable absorption time
• BatterySafe mode: preventing damage due to excessive gassing
• Storage mode: less maintenance and aging when the battery is not in use
• Smaller and lighter compared to similar models
• NMEA 2000 Canbus connection
• PowerControl: set a maximum shore power
• Remote Control
• Li-ion (LiFePo4) ready

 

Data sheet here

Manual here

 

NOTE: This unit requires installation by a licensed Electrician with Victron installation training. 

 

Features:

 

Skylla-i (1+1): two outputs to charge 2 battery banks- The Skylla-i (1+1) features 2 isolated outputs. The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery.

 

Skylla-i (3): three full current outputs to charge 3 battery banks- The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current.

 

Rugged- Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.

 

Flexible- Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use.

 

Synchronised parallel operation- Several chargers can be synchronised with the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP-cables. Please see the manual for details.

 

The right amount of charge for a lead-acid battery: variable absorption time- When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.

 

Preventing damage due to excessive gassing: the Battery Safe mode- If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-i will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.

 

Less maintenance and aging when the battery is not in use: the Storage mode- The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.

 

To increase battery life: temperature compensation- Every Skylla-i comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations of battery temperature are expected.

 

Battery voltage sense- In order to compensate for voltage loss due to cable resistance, the Skylla-i is provided with a voltage sense facility so that the battery always receives the correct charge voltage.

 

Use as a power supply- As a result of the perfectly stabilized output voltage, the Skylla-i can be used as a power supply if batteries or large buffer capacitors are not available.

 

Li-Ion (LiFePO4) ready- Simple charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively complete control of voltage and current can be achieved by connecting to the galvanically isolated CAN bus port.

SolarBox Australia will process your order within 1-2 business days. For product availability you can call us, use the chat function or email SolarBox directly at: jason@solarboxaustralia.au If there is a delay on your order or your item is out of stock you will be emailed immediately to let you know.

Shipping prices are calcuated at checkout depending on weight and where it is being shipped to. View the shipping rules here

What is a warranty? A warranty is a voluntary promise offered by the person or business who sold the product or service to you. Once you buy the product or service, the promise becomes a right that can be enforced under the ACL. Warranties are separate from your automatic consumer guarantees. The consumer guarantees which apply regardless of any warranties suppliers sell or give to you, apply for a reasonable time depending on the nature of the goods or services. This means consumer guarantees may continue to apply after the time period for the warranty has expired.

View the product warranty page here for more information.

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.